Alexis Mabanza @ alexvolkihar.ovh

Circuit

Printed circuit boards that were never made

Each piece is a printed circuit board that was never sent to a fab. The parts go down first, on a routing grid of about 0.635 mm per cell, from footprints drawn in their real proportions: SOIC and TSOP chips, quad flat packs, QFNs with their thermal pad, 0603 and 1206 resistors and capacitors, SOT-23 transistors, electrolytic capacitors, crystals, pin headers, TO-220 regulators, power inductors and screw terminals. A netlist then ties the pins together. Two chips facing each other get a bus, pin for pin and in order. Decoupling capacitors sit between the chips’ supply pins and ground, the main chip on a logic board gets a crystal with its two load capacitors, and every LED gets its resistor. Short point-to-point nets join the rest. On memory boards the chips stand in rows above a gold edge connector, and on power boards the regulators, inductors and bulk capacitors are chained by wide copper.

Each connection is then routed in turn, shortest first, by a maze router. It is an A* search over the grid that charges for every bend and every via, so a track runs straight, turns at 45° (or at right angles on some boards) and steps around everything laid before it. A connection that finds no way through drops to an inner layer through a via, as it would on a real board. Two-layer boards are routed on both faces, and the bottom layer shows faintly through the mask. Then the board is fabricated: a solid or hatched ground pour with a clearance gap around every other net and thermal spokes on the ground pads, a solder mask in green, blue, black, purple or white, gold pads, and a silkscreen legend with outlines, pin-1 dots, polarity marks and reference designators numbered in reading order. Some boards come back from assembly with their parts on. The lettering is drawn with a small stroke font written for the series. Press New seed for a fresh hash, then share the URL to show someone that exact piece.

All series
0x5be9ad8f…bda6
Mask GreenLayout MemoryRouting RoundedPour SolidAssembly Populated
0x42da1459…8fe0
Mask GreenLayout LogicRouting Two-layerPour NoneAssembly Bare
0x60788938…f336
Mask BlackLayout LogicRouting Two-layerPour HatchedAssembly Bare
0x9ee2c02a…5c61
Mask WhiteLayout MemoryRouting MitredPour NoneAssembly Populated
0xa6d50b20…99f3
Mask GreenLayout AnalogRouting Right-anglePour SolidAssembly Populated
0x218bc3cb…2874
Mask BlueLayout AnalogRouting Right-anglePour NoneAssembly Populated
0x6c9b02cb…e59a
Mask PurpleLayout PowerRouting MitredPour SolidAssembly Bare
0xd936016b…cbb9
Mask BlueLayout PowerRouting Right-anglePour SolidAssembly Populated
0xf598de23…b93a
Mask WhiteLayout LogicRouting Right-anglePour SolidAssembly Partial
0xbfe8354a…3912
Mask GreenLayout PowerRouting Right-anglePour SolidAssembly Bare
0xc9edbccf…5bf1
Mask PurpleLayout AnalogRouting MitredPour NoneAssembly Populated
0x956a3c02…0dcb
Mask BlueLayout LogicRouting MitredPour NoneAssembly Bare

Traits

The weights were set before any drawing code was written. They were then checked against a census of 2,000 seeds.

TraitValues (weight)
MaskGreen 34 · Blue 18 · Black 16 · Purple 16 · White 16
LayoutLogic 35 · Analog 25 · Power 20 · Memory 20
RoutingMitred 45 · Right-angle 25 · Rounded 15 · Two-layer 15
PourNone 40 · Solid 40 · Hatched 20
AssemblyBare 40 · Populated 40 · Partial 20

Credits

  • Routing: the grid maze router of C. Y. Lee ("An Algorithm for Path Connections and Its Applications", IRE Transactions on Electronic Computers, 1961), run as an A* search (P. E. Hart, N. J. Nilsson and B. Raphael, "A Formal Basis for the Heuristic Determination of Minimum Cost Paths", 1968) over states made of a cell, a layer and the direction of arrival, so that bends and vias can be priced. A 45° bend is cheap, a right angle dearer, and sharper turns are not allowed. Nets are routed one at a time, shortest first, and a diagonal step may not clip a pad or cross another diagonal.
  • Footprints: package pitches from the JEDEC outlines (1.27 mm SOIC, 0.65 mm quad flat packs and TSOP, 2.54 mm DIP) and common connector pitches (2.54 mm pin headers, 5.08 mm screw terminals). The reference designator letters (R, C, U, J, Y, Q, D, L, TP) follow ASME Y14.44.
  • Fabrication: ground pours with clearances and thermal reliefs, stitching vias, fiducials and mounting holes as they appear in ordinary PCB CAM output. The part numbers and markings are invented.
  • Lettering: an original single-stroke font, in the manner of the vector fonts used by pen plotters and photoplotters (after A. V. Hershey’s plotter fonts, 1967).
  • Randomness: sfc32 by Chris Doty-Humphrey, seeded from the hash with named sub-streams, following Camille Roux’s genart skill (MIT).
  • The palettes and the stroke font are original. The code was written with an AI assistant. It draws everything itself: no AI-generated images.

Artworks © Alexvolkihar, licensed CC BY-NC-ND 4.0. Code under the repository licence (MIT).


>